Transponder Programmer
Transponder: immo transponder, the transponder inside key, sometimes we call it chip
sub-remote-pcb: the remote PCB, used in Prepare Remote function. After write data with remote programmer, it can adapt to car for remote function
Remote Programmer: It is not standard device, This device can connect to DB15 in VVDI2, it can prepare remote key with sub-remote-pcb
Byte: a decimal value between 0-255, but we can’t input decimal value, we input hex value, every byte between 00-FF．
Note: For the byte use in transponder, every input character must belong to 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F
Note: For the byte use in transponder, every input character must belong to 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F
Transponders Types
1) PCF7930/PCF7931/PCF7935
2) HITAG2
3) HITAG2+ EE
4) HITAG2 Extended
5) HITAG3
6) HITAG Pro
7) HITAG (BMW)
8) HITAG (VAG)
9) MEGAMOS13
10) MEGAMOS48
11) MEGAMOS8E
12) TEMIC 11/TEMIC 12
13) TEMIC 8C
14) TIRIS 4C
15) TIRIS DST 4D/4E
16) TIRIS DST+
17) T5/TK5551
2) HITAG2
3) HITAG2+ EE
4) HITAG2 Extended
5) HITAG3
6) HITAG Pro
7) HITAG (BMW)
8) HITAG (VAG)
9) MEGAMOS13
10) MEGAMOS48
11) MEGAMOS8E
12) TEMIC 11/TEMIC 12
13) TEMIC 8C
14) TIRIS 4C
15) TIRIS DST 4D/4E
16) TIRIS DST+
17) T5/TK5551
Adjust Antenna of your device
You can make the antenna more stable with change gain value
For every key is different from each other, the transponder is different position in the key,
Thus will cause bad answer while access transponder. You can change antenna gain to large the sensing range, make antenna access the far away transponder
Thus will cause bad answer while access transponder. You can change antenna gain to large the sensing range, make antenna access the far away transponder
Antenna gain value can be 0, 1, 2, 3
When gain value smaller, the sensing range will be small and lower. If the transponder
position is higher from antenna, the access may failed
When gain value larger, the sensing range will be large and higher. If the transponder
position is lower from antenna, the access may failed
Simply:
If the transponder position is far away from antenna, you need select higher gain for
access, example: 2 or 3
If the transponder position is nearby or in antenna, you need select lower gain for access,
example: 0 or 1
position is higher from antenna, the access may failed
When gain value larger, the sensing range will be large and higher. If the transponder
position is lower from antenna, the access may failed
Simply:
If the transponder position is far away from antenna, you need select higher gain for
access, example: 2 or 3
If the transponder position is nearby or in antenna, you need select lower gain for access,
example: 0 or 1
Autodetect Transponder
Input transponder to VVDI2 programmer, press button “Autodetect Transponder”
Autodetect Transponder function can run without software,
just provide power to VVDI2, press button “T” on the device, transponder type will show in the LCD display
just provide power to VVDI2, press button “T” on the device, transponder type will show in the LCD display
