ELECTRONIC REPAIR COMPANY
  • HOME
  • AUTO File Services Portal
  • Protarge VI Testers
  • Chip Programmer
  • ECU Books
  • ONLINE Store
  • ECU Repair Manual
  • ECU Fault Locator
  • --- ERC Front Door---
  • FERRARI MASERATI REPAIR -
  • Auto Tuning Blog
  • Privacy Policy
  • Support Tickets
  • Headunit Repair Course
  • Book Practice Days
  • Auto Headunit Menu

Bosch M(G) 7.9.8 - the OBDII

This module is designed to record the FLASH memory and ECU M7.9.8 MG7.9.8 programming unit via the OBDII connector. Communication control unit takes place via the CAN bus via a J2534 compatible device.
ECU supports the following programming modes: 
Record FLASH, view the computer certificate
attention! Because not all computer firmware Bosch M7.9.8 , MG7.9.8 interchangeable among themselves a foreign EEPROM write operation (based on the other software versions) can lead to the fact that the computer can not be started after the recording. 

In this case, the control unit can restore Bosch M7.9.8 module.However, in this case it is necessary to remove and disassemble the computer.

ChipLoader loader performs a series of operations to determine the firmware compatibility, but does not account for all the options.

The size of the firmware FLASH memory Bosch M7.9.8, MG7.9.8 - 832 KB (851,968 bytes).

To configure the computer to work with the data there is a separate tab in the program settings window:
Picture
Repeatedly flashing the ECU recommend that you select the option "Record only calibration control unit Bosch M (G) 7.9.8". This will speed up the process of rewriting the firmware.

Operation record only for calibration of the unit is completely safe. In case of failure you can always redo the recording operation by OBDII connector. However, in some cases, after the failure in recording calibration to establish communication with the ECU is required to disconnect it briefly for a few seconds.

​

In the case of the recording field calibration and region by unsafe site to record is to record addresses of 0x0000-0x8000 range. If an error occurs during recording of the site need to recover the computer using a Bosch M7.9.8 module with the removal and disassembly of the computer.

Connecting to a Computer M 7.9.8 connector on the table


2 - ECU GND

82 - continuous power (+ 12V)

83 - Ignition (+12)

84 - CAN-H

62 - CAN-L

Connecting to a computer terminal MG7.9.8 on the table:

Large connector:

2 - ECU GND

6 - +12

Small connector:

11 - +12

12 - CAN-H

27 - CAN-L

56 - +12

 

BACK TO CHIPLOADER
Please note that we don't accept Orders / support requests sent direct to our email address.




Privacy Policy
Picture
Picture

    Contact Us

    Your Name ( First & Last)
    Email
    Country
    This issue or suggestion is regarding
    Tell us how we can help
    Max file size: 20MB
Submit




Contact us



AUTO BLOG


All Rights Reserved, ©2011  Electronic Repair Company
Auto Blog

buy stocks with bitcoin, buy stock with bitcoin, how to invest in bitcoin stock, compare car insurance, auto insurance troy mi, car insurance comparison quote, cars with cheapest insurance rates, insurance quotes young drivers, california motorcycle accident lawyer, car accident lawyer in phoenix, auto accident lawyers in chicago, phoenix accident attorneys, car accident lawyer ny, motorcycle accident attorney orange county, compensation mesothelioma, mesothelioma compensation, lawyers for mesothelioma ,Accept Bitcoin and other crypto payments

  • HOME
  • AUTO File Services Portal
  • Protarge VI Testers
  • Chip Programmer
  • ECU Books
  • ONLINE Store
  • ECU Repair Manual
  • ECU Fault Locator
  • --- ERC Front Door---
  • FERRARI MASERATI REPAIR -
  • Auto Tuning Blog
  • Privacy Policy
  • Support Tickets
  • Headunit Repair Course
  • Book Practice Days
  • Auto Headunit Menu