Bosch MP 7.0
Reading FLASH
This option lets you read only addresses calibration information recorded in the FLASH memory of the control unit. Full FLASH memory contents schtityvanie considered in this way will not work. Edinstvennnoe what can be done - vypayat using soldering station FLASH memory of the unit and to consider it in progrmmatore. FLASH memory readout occurs at a low exchange rate (lack of block), therefore reading namnogim calibration takes more time than their recording.
size calibrations FLASH memory is 32KB (32768 bytes)
Attention! The "Read the Flash" is made only when the computer will be transferred to the diagnosis of the condition.
FLASH Programming
Writing in the FLASH memory of the computer depends on the contents on the clipboard as an area calibrations addresses, and the entire contents (FULL FLASH).Record flash is largely determined by the size of the firmware, which is contained in the program clipboard.
firmware size, field calibrations addresses - 32KB (32768 bytes), the entire size of the entire firmware is - 256 KB (262,144 bytes).
Attention! "Burn the Flash" mode should be made only when the control unit will be transferred to the programming mode.
ECU passport (ID)
This option displays the firmware block identifiers, as well as data to the control unit.
Attention! The option "ECU passport" only when the control unit will be transferred to the diagnostic mode.
Connecting to a computer terminal
19 conclusion - GND
55 conclusion - K-Line
27 conclusion - Ignition (+12)
18 conclusion - continuous voltage supply (+ 12V)
50 withdrawal of ECU - Programming Resolution (+ 12V through resistor order 4KOm) - FLASH is served only when recording.
37 conclusion - Power of the main relay (+ 12V)
When programming programmer PBB-2 to convert the block into the programming mode Put the switch on the 55 pin connector in position "II".
We recommend that before making a chip tuning, to learn whether there is a possibility to change the car's ECU program. Many brands of cars are equipped with a control unit, in connection with which the firmware of these units is practically impossible to change because it is not available for reading and zapisi.Esli reprogram the computer for the first time - read the reprogu of computer instructions, so as not to put the unit and do not get to buy a new, and it is sometimes not very deshevo.Obyazatelno will have to make a complete diagnosis of the vehicle before flashing that there is no misunderstandings about the failed car after chip tuning.
This option lets you read only addresses calibration information recorded in the FLASH memory of the control unit. Full FLASH memory contents schtityvanie considered in this way will not work. Edinstvennnoe what can be done - vypayat using soldering station FLASH memory of the unit and to consider it in progrmmatore. FLASH memory readout occurs at a low exchange rate (lack of block), therefore reading namnogim calibration takes more time than their recording.
size calibrations FLASH memory is 32KB (32768 bytes)
Attention! The "Read the Flash" is made only when the computer will be transferred to the diagnosis of the condition.
FLASH Programming
Writing in the FLASH memory of the computer depends on the contents on the clipboard as an area calibrations addresses, and the entire contents (FULL FLASH).Record flash is largely determined by the size of the firmware, which is contained in the program clipboard.
firmware size, field calibrations addresses - 32KB (32768 bytes), the entire size of the entire firmware is - 256 KB (262,144 bytes).
Attention! "Burn the Flash" mode should be made only when the control unit will be transferred to the programming mode.
ECU passport (ID)
This option displays the firmware block identifiers, as well as data to the control unit.
Attention! The option "ECU passport" only when the control unit will be transferred to the diagnostic mode.
Connecting to a computer terminal
19 conclusion - GND
55 conclusion - K-Line
27 conclusion - Ignition (+12)
18 conclusion - continuous voltage supply (+ 12V)
50 withdrawal of ECU - Programming Resolution (+ 12V through resistor order 4KOm) - FLASH is served only when recording.
37 conclusion - Power of the main relay (+ 12V)
When programming programmer PBB-2 to convert the block into the programming mode Put the switch on the 55 pin connector in position "II".
We recommend that before making a chip tuning, to learn whether there is a possibility to change the car's ECU program. Many brands of cars are equipped with a control unit, in connection with which the firmware of these units is practically impossible to change because it is not available for reading and zapisi.Esli reprogram the computer for the first time - read the reprogu of computer instructions, so as not to put the unit and do not get to buy a new, and it is sometimes not very deshevo.Obyazatelno will have to make a complete diagnosis of the vehicle before flashing that there is no misunderstandings about the failed car after chip tuning.
